BTEX EMISSIONS FROM BioCo2 BONDED MOULDING SANDS

Authors

  • Joanna Loch AGH University of Science and Technology, Faculty of Foundry Engineering, Krakow, Poland
  • Beata Grabowska AGH University of Science and Technology, Faculty of Foundry Engineering, Krakow, Poland
  • Karolina Kaczmarska AGH University of Science and Technology, Faculty of Foundry Engineering, Krakow, Poland

DOI:

https://doi.org/10.7494/mafe.2013.39.1.23

Keywords:

moulding sands, polymer binders, gas emissions, gas chromatography

Abstract

The aim of the research was to determine the volume of BTEX emission (benzene, toluene, ethylbenzene and xylenes) from BioCo2 bonded moulding sands. BioCo2, a new polymer binder, is a water solution of two - component polymer composition
(polyacrylic acid and dextrin).

Research on gas emissions were performed according to the method developed at Faculty of Foundry Engineering, AGH University of Science and Technology. The measurement
of BTEX samples adsorbed on activated carbon was made with the use of gas chromatography (GC-FID) and was followed by a qualitative and quantitative analysis. The research showed that the volume of BTEX emissions was lower in BioCo2 bonded moulding sand than in resin-bonded sand Kaltharz U404.

Downloads

Download data is not yet available.

References

A.P. Li, F. Müller, A. Birner, K. Nielsch, U. Gösele, J. Vac. Sci. Technol. A 17 (1999) 1428–1431

D. Navas, A. Asenjo, M. Jaafar, K.R. Pirota, M. Hernández-Veléz, R. Sanz, W. Lee, K. Nielsch,

F. Batallan, M. Vázquez, J. Magn. Magn. Mater. 290-291 (2005) 1991

A. Foyet, A. Hauser, W. Schäfer, Mater. Sci. Eng. C27 (2007) 100

K. Nielsch, F. Müller, A.P. Li, U. Gösele, Adv. Mater. 12 (8) (2000) 582

Y. Henry, K. Ounadjela, L. Piraux, S. Dubois, J.M. George, J.L. Duvail, Eur. Phys. J. B 20 (2001) 35

A. Fert, L. Piraux, J. Magn. Magn. Mater. 200 (1999) 338

J.M. Garcia, A. Asenjo, M Vázquez, P. Aranda, E. Ruiz-Hitzky, IEEE Trans. Magn. 36 (2000) 2981

J. Ung Cho, J-H Wu, J. Hyun Min, S. Pil Ko, J. Young Soh, Q. Xian Liu, Y. Keun Kim, J. Magn. Magn. Mater 303 (2006) e281

M. Darques, L. Piraux, A. Encians, P. Bayle-Guillemaund, A. Popa, U. Ebels, Applied. Physics Letters 86 (2005) 072508 31

N.B. Chaure, P. Stamenov, F.M.F. Rhen, J.M.D. Coey, J. Magn. Magn. Mater 290–291 (2005) 1210

D.H. Qin, M. Lu, F.L. Li, Chem. Phys. Lett. 350 (2001) 51

K.I. Arai, H.W. Kang, K. Ishiyama, IEEE Trans. Magn. 27 (1991) 4906

H.R. Khan, K. Petrikowski, Mater. Sci. Eng. C 19 (2002) 345

D.H. Qin, L. Cao, Q.Y. Sun, Y.Huang, A.L. Li, Chem. Phys. Lett. 358 (2002) 484

H. Masuda, K. Fakada, Science 268 (1995) 1466

J. Li, C. Papadopoulos, J. Xu, Nature 402 (1999) 253

M. Ciureanu, F. Beron, L. Clime, P. Ciureanu, A. Yelon, T.A. Ovari, R.W. Cochrane, F. Normandin,

T. Veres, Electrochimca Acta 50 (2005) 4487–4497

R. Inguanta, S. Pizza, C. Sunseri, Electrochimca Acta 53 (2008) 5766–5773

Downloads

How to Cite

Loch, J., Grabowska, B., & Kaczmarska, K. (2014). BTEX EMISSIONS FROM BioCo2 BONDED MOULDING SANDS. Metallurgy and Foundry Engineering, 39(1), 23. https://doi.org/10.7494/mafe.2013.39.1.23

Issue

Section

Articles

Most read articles by the same author(s)

<< < 1 2