FEATURES OF 2017A AND AlSi9Mg ALUMINUM ALLOYS FRICTION STIR WELDED WITH ROOT-SIDE HEATING

Authors

  • Krzysztof Mroczka Pedagogical University of Cracow
  • Adam Pietras Institute of Welding
  • Jerzy Jura Pedagogical University of Cracow

DOI:

https://doi.org/10.7494/mafe.2016.42.2.105

Keywords:

aluminium alloys, friction stir welding, heating, structure, mechanical properties

Abstract

Aluminum alloys 2017A and AlSi9Mg (hypo-eutectic silumin) were friction stir welded with a relatively high linear velocity (over 1 m/min) and use of an additional heat source from the root side of the weld. Macrostructure investigation (with high-resolution images) showed no effect of heating on weld quality. The welding process caused significant fragmentation of the secondary phases in the AlSi9Mg alloy. Furthermore, it was proven that the material above the weld nugget was not mixed and contained micro-defects that were not caused by welding. Also, it contained cavities on the boundaries between Si-particles and the matrix. Based on hardness distribution, a slight strengthening of the cast alloy was observed at the bottom and middle parts of the weld. However, the hardness of the 2017A alloy initially decreased and then increased due to natural aging. This means that the FSW process produced a metastable state in the alloy.

Downloads

Download data is not yet available.

References

Fraś E., Janas A., Kurtyka P., Wierzbiński S.: Structure and properties of cast Ni3Al/TiC and Ni3Al/TiB2 composites. PART II. Investigation of mechanical and tribological properties and of corrosion resistance of composites based on intermetallic phase Ni3Al reinforced with particles of TiC and TiB2. Archives of Metallurgy and Materials, 49, 1 (2004), 113–141

Kurtyka P., Ryłko N.: Structure analysis of the modified cast metal matrix composites by use of the RVE theory. Archives of Metallurgy and Materials, 58, 2 (2013), 357–360

Hajjari M., Divandari E.: An investigation on the microstructure and tensile properties of direct squeeze cast and gravity die cast 2024 wrought Al alloy. Materials and Design, 29 (2008), 1685–1689

Uzun H., Donne C.D., Argagnotto A., Ghidini T., Gabaro C.: Friction stir welding of dissimilar Al 6013-T4 To X5CrNi18-10 stainless steel. Materials and Design, 26 (2005), 41–46

Fraś E., Olejnik E.: Interaction between solidification front and alien phase particles. Archives of Metallurgy and Materials, 53, 3 (2008), 695–702

Yeni C., Sayer S., Ertugrul O., Pakdil M.: Effect of post-weld aging on the mechanical and microstructural properties of friction stir welded aluminum alloy 7075. Archives of Materials Science and Engineering, 34, 2 (2008), 105–109

Węglowski M.S., Pietras A.: Friction Stir Processing – analysis of the process. Archives of Metallurgy and Materials, 56, 3 (2011), 779–788

Kurtyka P., Ryłko N., Tokarski T., Wójcicka A., Pietras A.: Cast aluminium matrix composites modified with using FSP process. Changing of the structure and mechanical properties. Composite Structures, 133 (C)

(2015), 959–967

Mroczka K., Pietras A.: Characteristics of dissimilar Friction Stir Welded joints of selected aluminum alloys. Proceedings of Conference: Materials Science and Technology. Pittsburgh PA, USA, Joining of Advanced and Specialty Material, (2012), 308–315

Shusheng D., Xinqi Y., Guohong L., Bo J.: Comparative study on fatigue properties between AA2024-T4 friction stir welds and base material. Materials Science and Engineering A, 435–436 (2006), 389–395

Adamowski J., Gambaro C., Lertora E., Ponte M., Szkodo M.: Analysis of FSW welds made of aluminium alloy AW6082-T6. Archives of Materials Science and Engineering, 28, 8 (2007), 453–460

Węglowski M.S., Dymek S.: Microstructural modification of cast aluminium alloy AlSi9Mg via Friction Modified Processing. Archives of Metallurgy and Materials, 57 (2012), 71–78

Bala Srinivasan P., Arora K.S., Dietzel W., Pandey S., Schaper M.K.: Characterization of microstructure, mechanical properties and corrosion behavior of an AA2219 friction stir weldment. Journal of Alloys and Compounds, 492 (2010), 631–637

Yuan W., Mishra R.S., Webb S., Chen Y.L., Carlson B., Herling D.R., Grant G.J.J.: Effect of tool design and process parameters on properties of Al alloy 6016 friction stir spot welds. Journal of Materials Processing Technology, 211 (2011), 972–977

Węglowski M.S., Pietras A., Węglowska A.: Effect of welding parameters on mechanical and microstructural properties of Al 2024 joints produced by friction stir welding. Journal of Kones Powertrain and Transport, 19 (2009), 523–532

Wójcicka A., Wróbel Z.: The Panoramic visualization of metallic materials in macro- and microstructure of surface analysis using microsoft image composite editor (ICE). Lecture Notes in Computer Science, 7339 (2012), 358–368

Kishawy H.A., Li L., El-Wahab A.I.: Prediction of chip flow direction during machining with self-propelled rotary tools. International Journal of Machine Tools and Manufacture, 46 (2006), 1680–1688

Mroczka K., Pietras A.: Characteristics of FSW welds of aluminum alloys – casted elements with rolled elements. Proceedings of Conference: 9th Friction Stir Welding Symposium, Huntsville, USA (2012)

Mrówka-Nowotnik G., Sieniawski J., Wierzbińska M.: Intermetallic phase particles in 6082 aluminium alloy. Archives of Materials Science and Engineering, 28, 2 (2007), 69–76

Mroczka K.: Characterization of the microstructure and properties of FSW welds of selected aluminum alloys. Scientific Publishing of Pedagogical University of Cracow, Krakow 2014

SigmaScanPro5, User’s Guide, 2004

Mroczka K.: The effect of FSW parameters on the microstructure and properties of 2017A/AlSi9Mg aluminium alloy welds. Materials Engineering, 4, 194 (2013), 328–331

Ridley N., Bate P.S., Zhang B.: Effect of strain rate path on cavitation in superplastic aluminium alloy Materials Science and Engineering A, 463 (2007), 224–230

Sato Y.S., Urata M., Kokawa H., Ikeda K.: Hall/Petch relationship in friction stir welds of equal channel angular-pressed aluminium alloys. Materials Science and Engineering A, 354 (2003), 298–305

Genevois C., Fabregue D., Deschamps A., Poole W.J.: On the coupling between precipitation and plastic deformation in relation with friction stir welding of AA2024 T3 aluminium alloy. Materials Science and Engineering A, 441 (2006), 39–48

Mroczka K., Wójcicka A., Kurtyka P.: Acta Metallurgica Slovaca, 18, 2–3 (2012), 82–91

Downloads

Published

2017-01-26

How to Cite

Mroczka, K., Pietras, A., & Jura, J. (2017). FEATURES OF 2017A AND AlSi9Mg ALUMINUM ALLOYS FRICTION STIR WELDED WITH ROOT-SIDE HEATING. Metallurgy and Foundry Engineering, 42(2), 105. https://doi.org/10.7494/mafe.2016.42.2.105

Issue

Section

Articles